钛酸锶光催化剂的改性研究进展

钛酸锶（SrTiO3）光催化剂是一种钙钛矿型三元氧化物,具有较强的氧化还原能力、良好的物理化学稳定性及环境友好等特点,在光催化各领域得到了广泛应用,如制氢/降解/光电催化等。SrTiO3对太阳光的利用率较低,且其本征光催化活性受光生载流子分离效率等因素限制,阻碍了实际应用。针对以上问题,将围绕国内外SrTiO3改性研究的现状进行综述,主要从掺杂、负载、复合改性等方面进行陈述。最后,对高效稳定SrTiO3光催化剂的未来发展趋势进行展望。     

Sr0.6Ba0.2Ca0.2Al2O4 ∶Eu,Dy的制备与长余辉发光性能研究

采用高温固相法制备了Ca,Ba共掺的Sr_0.6Ba_0.2Ca_0.2Al₂O₄ ∶Eu²⁺_0.01, Dy³⁺_0.02和单掺Ba的Sr_0.6Ba_0.4Al₂O₄ ∶Eu²⁺_0.01, 关键词： 长余辉 铝酸锶 稀土掺杂 陷阱能级     

Electrical and thermal properties of lead titanate glass ceramics

Glass samples with composition of (50−X)PbO-(25+X)TiO₂-25B₂O₃ (where X=0, 5, 10 and 12.5 mol%) were prepared using conventional quenching technique. The glass transition temperature, T_g and crystallization temperature T_c were determined from the DTA. These glass samples were converted to glass ceramics by following two stage heat treatment schedule. The glass ceramic samples were characterized by XRD, SEM and dielectric constant measurements. The XRD results revealed the formation of ferroelectric lead titanate (PT) as a major crystalline phase in the glass ceramics. The density increases and the CTE decreases for all glass ceramics with increase in X (mol%). This may be attributed to increase in PT phase. The SEM results which show rounded crystallites of lead titanate, also supports other results. Hysteresis loops observed at room temperature confirms the ferroelectric nature of glass ceramics. The optimized glass ceramic sample exhibits high dielectric constant which is of technical importance.     

纳米结构钛酸盐电极快速测定水体COD

分析了纳米结构钛酸盐电极快速测定COD的基本原理及COD标准物质定值方法。通过对纳米结构钛酸盐表征分析,钠型钛酸盐电极具有较高的灵敏度,外加0.7 V工作电位,测定COD溶液标准物质的线性相关系数大于0.995,误差在±8%以内;与国标方法比较,测量同一水样的误差在±15%以内。纳米结构钛酸盐电极可用于测量水体COD。     

Ba_3(PO_4)_2:Ce~(3+),Dy~(3+)荧光粉的组成与发光特性研究

在活性炭还原气氛下高温固相法合成了Ba3(PO4)2:Ce3+,Dy3+紫外发射荧光粉。XRD图谱表明,烧结温度为1100℃时保温处理3 h,样品为单相的Ba3(PO4)2型六方晶系结构。荧光光谱显示:单掺Ce3+样品中,Ce3+掺杂浓度为8%(摩尔分数)时样品的发光最强,发射峰的位置处在350 nm附近(Ce3+的2D→2F5/2和2D→2F7/2跃迁发射)。适量的Sr2+取代部分Ba2+离子,改变了基质晶格环境,使样品的发光强度得到提高且发射峰向长波方向红移。引入Dy3+作为敏化剂,样品发射峰红移到386 nm,亮度增强,主要是由于Dy3+和Ce3+之间发生了有效的能量传递过程。确定了Dy3+的最佳掺杂浓度为3%,发光强度提高了27%。     

卟啉敏化的钛酸盐纳米管的可见光催化活性

制备了四碘化5,10,15,20-四(对-N,N,N三甲基苯胺基)卟啉敏化的钛酸盐纳米管(TAPPI-TNTs),并利用甲基橙(MO)作为模型污染物考察了其可见光催化活性。结果表明,TAPPI-TNTs是一个高效的可见光催化剂,在其催化作用下,可见光照射1 h后,甲基橙的降解率为89%。与此相反,纯钛酸盐纳米管并不具有可见光催化活性。此外,TAPPI-TNTs的稳定性较高,可以多次循环使用,在第五次循环中,甲基橙的降解率仍可达到50%以上。这可能是由于带正电荷的卟啉与带负电荷的钛酸盐纳米管之间存在着较强的静电吸引作用,卟啉紧密地吸附在钛酸盐纳米管上,导致卟啉的光激发电子易于向钛酸盐纳米管转移,从而使钛酸盐纳米管得到了有效敏化。     

结构稳定的CuO/TiO2纳米管的功能化溶胶修饰法制备及其催化CO氧化性能研究

以水热处理方法得到的钛酸纳米管为载体,采用含有醋酸铜的功能化钛溶胶对其进行一步浸渍修饰,制备结构稳定的CuO修饰TiO₂纳米管催化剂(CuO/TiO₂NTs)。通过XRD(X-射线衍射)、TEM(透射电子显微镜)、HR-TEM(高倍透射电子显微镜)、XPS(X-射线光电子能谱)、BET(氮气吸附-脱附法)、TPD(程序升温脱附法)等表征材料的结构和性质,并研究其催化CO氧化的性能。研究表明：经过溶胶浸渍处理过程,不仅将功能化铜组分负载在纳米管上,而且纳米管载体的耐热性能明显提高;催化剂载体、铜钛原子比及焙烧温度对催化剂的活性有明显影响,且400℃焙烧的Cu/Ti原子比为1∶5的CuO/TiO₂NTs的活性最高。     

Ba0.6Sr0.4TiO3/聚偏氟乙烯-聚甲基丙烯酸甲酯复合材料的制备及其介电性能

采用流延热压工艺制备Ba_0.6Sr_0.4TiO₃(BST)/聚偏氟乙烯(PVDF)?聚甲基丙烯酸甲酯(PMMA)复合薄膜,研究了PMMA含量对复合材料微观组织结构和介电性能的影响规律。结果表明,BST相能够均匀分散在聚合物基体中,归因于PMMA与PVDF良好的相容性,2种聚合物之间的界面不分明;随着PMMA含量的增加,复合材料的介电常数先降低后升高,耐击穿强度和介电可调性先增加后减少。PMMA含量(体积分数)为15%的BST/PVDF?PMMA₁₅复合材料的综合性能最佳:介电常数为23.2,介电损耗为0.07,耐击穿强度为1412 kV·cm^-1,在550 kV·cm^-1偏压场下,介电可调性为26.2%。     

Magnetic properties of La-Co substituted M-type strontium hexaferrites prepared by polymerizable complex method

Magnetic properties of La-Co substituted M-type strontium hexaferrites were studied. The samples were prepared by polymerizable complex method. Crystal structure of samples has been investigated by powder X-ray diffraction (XRD). Single-phase M-type strontium hexaferrites with chemical composition of Sr_1.05−xLa_xFe_12−xCo_xO₁₉ (x=0-0.4) were formed by heating at 1173 K for 24 h in air. Magnetic properties were discussed by measurements of M-H curves with vibrating sample magnetometer (VSM). La-Co substituted M-type strontium hexaferrites prepared by polymerizable complex method showed typical magnetic hysteresis of hard ferrite. The coercive force increased significantly by La-Co substitution with polymerizable complex method. Maximum coercive force achieved in this study is 8.0 kOe (640 kA/m). Scanning electron microscopy revealed that the prepared ferrite particles have plate-like shape of diameter range between 20 and 500 nm.